Vital for barrier-free access: the status display. This provides the hard of hearing with clear feedback from the intercom.

Why not pick up a door call on your telephone, mobile or PC? Interfaces create transition points to the telephone system, the PC network or the intelligent home.

Classical with a receiver or as a handsfree unit, mounted on the wall or table, as a standard model or with deluxe functions in a metal, wood or paintwork finish – the choice is yours.

Hearing, speech, door release – the classical intercom system forms the basis of all door communication. At Siedle, this basis offers a starting point for expansion and upgrading. Four design lines and countless style variants address every conceivable requirement and personal preference.

Classical with a receiver or as a handsfree unit, mounted on the wall or table, as a standard model or with deluxe functions in a metal, wood or paintwork finish – the choice is yours.

Software extension for OSDP V2 protocol

(Reader addresses 4 to 7)

Hint: XMP-K32EX-F2 & XMP-K32EX-F17 required

Software extension for OSDP V2 protocol

(Reader addresses 0 to 3)

Software extension for OSDP V2 protocol

(Reader addresses 0 to 1)

Software extension for OSDP V2 protocol

(Reader addresses 4 to 7)

Hint: XMP-K32-F2 & XMP-K32-F17 required

Software extension for OSDP V2 protocol

(Reader addresses 0 to 3)

Software extension for OSDP V2 protocol

(Reader addresses 4 to 7)

Hint: XMP-K32SX-F2 & XMP-K32SX-F17 required

Software extension for OSDP V2 protocol

(Reader addresses 0 to 3)

Downloads
Guide – OSDP-V2 Protocol V1.0
Integration – OSDP-V2 Crypto Protocol

Software extension for OSDP V2 protocol

(Reader addresses 0 to 1)

Surcharge – PZ rose oval (for XMP-CX4-000 & -001)

Surcharge – blind rose PZ oval (for XMP-CX4-000 & -001)

Surcharge – PZ rose round (for XMP-CX4-000 & -001)

Surcharge – blind rose PZ round (for XMP-CX4-000 & -001)

Surcharge lever handle U2 form door handle mechanical side (for XMPCX4-000/-002/)

Surcharge lever handle U1 form door handle mechanical side (for XMPCX4-000/-002)

Surcharge lever handle U2 form door handle electronic side (for XMP-CX4-000/-001/-002/-003)

Surcharge lever handle U1 form door handle electronic side (for XMP-CX4-000/-001/-002/-003)

Electronic door handle, indoor, basic version, form L1, oval rose, electronic access on both sides

MIFARE Classic® & MIFARE® DESFire® EV1

Electronic door handle, indoor, basic version, form L1 for fire and smoke control doors, ovaL rose, electronic access on one side

MIFARE Classic® & MIFARE® DESFire® EV1

Electronic door handle, indoor, basic version, form L1, oval rose, electronic access on one side

MIFARE Classic® & MIFARE® DESFire® EV1

Electronic door handle, indoor, basic version, form L1, round rose, electronic access on both sides

MIFARE Classic® & MIFARE® DESFire® EV1

Electronic door handle, indoor, basic version, form L1 for fire and smoke control doors, round rose, electronic access on one side

MIFARE Classic® & MIFARE® DESFire® EV1

Electronic door handle, indoor, basic version, form L1, round rose, electronic access on one side

MIFARE Classic® & MIFARE® DESFire® EV1

SecuCrypt® radio module with long antenna for connection to door control unit (RS485) for maximum 8 electronic knob cylinders, door fittings, door handles.

Radio communication via 868 MHz (AES128)

SecuCrypt® radio module with short antenna for connection to door control unit (RS485) for maximum 8 electronic knob cylinders, door fittings, door handles.

Radio communication via 868 MHz (AES128)

MIFARE Classic®, MIFARE® DESFire® EV1 & EV2 card reader with PIN code and 4 function keys for connection to door controller (Color: black; protection class: IP54)

Hearing is good. Seeing is safer. Taking an unmistakable close look beats asking “who is it?” every time. A video surveillance system provides a significant gain in terms of both security and convenience over conventional intercom systems. And all with the added bonus of the outstanding installation and design versatility offered by Siedle systems.

MIFARE Classic®, MIFARE® DESFire® EV1 & EV2 card reader for connection to door controller (Color: black; protection class: IP54)

Spotlights illuminate details such as keypads, house numbers or fingerprint readers. By directing the light, it is possible to accentuate edges and contours. A white high-powered LED is used as a light source.

The surface area light provides the perfect illumination for company names, logos and inscriptions, while attracting action in its own right with its innovative design.

The square light module forms the basis for low-profile wall lights or free-standing light pedestals. Every module is equipped with four LEDs, which remain recognizable as spot-shaped light sources. Vertical in-row mounting results in different illumination scenarios and luminous densities.

Card Readers using Wiegand® or RS485 protocol can be connected to Door Controllers via XMP-RIM module.

The XMP-RIM module detects different protocol types automatically without particular configuration. The module provides access control via supervised inputs and relay outputs by sending the access card data to a door controller. The controller checks the validity of the access card. If the appropriate permissions have been assigned, the controller sends a message back to the XMP-RIM module allowing to unlock the door and provide access.

The following variants are available:

• XMP-RIM-001 single reader board
• XMP-RIM-002 double reader board
• XMP-RIM-003 single reader board Wiegand®
• XMP-RIM-004 double reader board Wiegand®
• XMP-RIM-005 double reader board Wiegand® without in- and outputs

Technical details:

• Power supply 12/24V DC
• Current consumption max. 3VA without peripheral devices
• Firmware update via software upload
• Max. 4 supervised inputs, 2 relay outputs
• Dimensions:
  XMP-RIM-00x: 97 x 97 x 25mm
  XMP-RIM-0x0: 125 x 125 x 30mm
  XMP-RIM-0x1: 140 x 140 x 75mm
  XMP-RIM-0x2: 235 x 345 x 125mm
• Supported Wiegand® formats:
  8 Bit transmission of numeric keypad information
  24 Bit transmission of 6 half-bytes (without parity check)
  26 Bit standard HID format
  32 Bit 4 bytes decimal (without parity check)
  34 Bit Siedle®-Vario
  35 Bit Corporate 1000 (HID)
  36 Bit Deister® MIFARE® Classic UID
  37 Bit HID-Controlled format
  40 Bit 5 bytes decimal (without parity check)
  44 Bit Deister® format TPD112

• 16 supervised inputs with 4 states (interruption, alarm, normal state, short circuit)
• Connection to the Door Control Unit XMP-K32 / XMP-K32sx (via RS485 interface) or additional to the local control module XMP-96 (via VCOM card)
• Up to 16 connectable XMP-KDM-016 modules per XMP-K32
• Supply voltage 12-24 V AC/DC via door control units

• 8-channel relay extension board for the direct switching of loads for electric door openers, optical signal devices or acoustic signal devices like horns, lamps via XMP-KDA-024 switching module
• The 24 switch commands of XMP-KDA-024 module can be extended by connection of 3 XMP-KDR-008 with 8 relays each.
• The address settings of the relay board are configured by jumpers (KDR0 to KDR2).
• The relay outputs can be set by jumpers either as control voltage applied or as dry contact.

• XMP-KDA-024 extends XMP Door Controllers with additional 24 binary outputs
• Insert to activate presence indicator boards
• Connection to XMP-K32 / XMP-K32sx via integrated RS485 interface

Controller for connecting the palm vein reader XMP-TMC2801-PV to XMP-BABYLON.

Features:

• Application for palm vein algorithm
• Real-time Linux operating system

GPL License Text Linux-Kernel Version 2.6.15.7 / BusyBox Version 1.10.3

XMP-BABYLON provides encrypted online communication to Aperio™ wireless door locks or door cylinders.

The integrated RFID readers transfer data via wireless link to a communication hub. The Hub is connected to the controller XMP-CMM, which transfers data to the host.

Features:

• Connection of 4 (with license key up to 8) RFID card readers
• Integration of MIFARE® Classic / DESFire® EV1 RFID technology
• Integration of HID® iCLASS® RFID technology
• Full functionality for online and offline mode of XMP-CMM
• Online administration of the access rights for different door locks/door cylinders
• Possibility of integrating XMP-CMM in an existing access control system

GPL License Text Linux-Kernel Version 2.6.15.7 / BusyBox Version 1.10.3

XMP-K12 19″ door controller can be used to connect up to two reader for intelligent access control, time recording, time management, gate control, safeguard control, camera control, parking space count, light control, for biometrical systems, RFID chip, elevator control up to 192 floors etc.

Technical details:

• Offline storage for up to
  15.000 badges (extendable via software license)
  50.000 bookings
  25.000 access profiles (extendable via software license)
• Connection for up to 2 card reader
• Connection for up to 2 IP network cameras for event driven picture recording
• 8 supervised inputs (short cut and interruption)
• 4 outputs (1A max 24V)
• Optionally with global In/Out control in offline mode
• Network connection via integrated 10/100 MBit Ethernet connector
• 2 GB MicroSD card to store data and programs
• 64 time schedules
• 64 routines (small user programs)
• 16 graphical ViPS programs
• Calender with holiday definitions
• Elevator control with access profile for up to 192 levels using XMP-KDA-024
• ‘Power over Ethernet’ instead of power supply possible
• 256-bit Blowfish- or AES encryption
• Encrypted reader communication using SecuCrypt®
• Real-time Linux operating system

GPL License Text Linux-Kernel Version 2.6.15.7 / BusyBox Version 1.10.3

XMP-K12 door controller can be used to connect up to two reader for intelligent access control, time recording, time management, gate control, safeguard control, camera control, parking space count, light control, for biometrical systems, RFID chip, elevator control up to 192 floors etc.

Technical details:

• Offline storage for up to
  15.000 badges (extendable via software license)
  50.000 bookings
  25.000 access profiles (extendable via software license)
• Connection for up to 2 card reader
• Connection for up to 2 IP network cameras for event driven picture recording
• 8 supervised inputs (short cut and interruption)
• 4 outputs (1A max 24V)
• Optionally with global In/Out control in offline mode
• Network connection via integrated 10/100 MBit Ethernet connector
• 2 GB MicroSD card to store data and programs
• 64 time schedules
• 64 routines (small user programs)
• 16 graphical ViPS programs
• Calender with holiday definitions
• Elevator control with access profile for up to 192 levels using XMP-KDA-024
• Integrated UPS
• ‘Power over Ethernet’ instead of integrated power supply and UPS possible
• 256-bit Blowfish- or AES encryption
• Encrypted reader communication using SecuCrypt®
• Real-time Linux operating system

XMP-K32sx 19″ door controller can be used for intelligent access control, time recording, time management, gate control, safeguard control, camera control, parking space count, light control, for biometrical systems, RFID chip, elevator control up to 192 floors etc.

Technical details:

• Offline storage for up to
  15.000 badges (extendable via software license)
  50.000 bookings
  25.000 access profiles (extendable via software license)
• Connection for up to 4 card reader (can be extended to 8)
• Connection for up to 4 IP network cameras for event driven picture recording
• 16 supervised inputs (short cut and interruption)
• 8 outputs (1A max 24V)
• Optionally with global In/Out control in offline mode
• Network connection via integrated 10/100 MBit Ethernet connector
• 2 GB MicroSD card to store data and programs
• 64 time schedules
• 64 routines (small user programs)
• 16 graphical ViPS programs
• Calender with holiday definitions
• Elevator control with access profile for up to 192 levels using XMP-KDA-024
• 256-bit Blowfish- or AES encryption
• Encrypted reader communication using SecuCrypt®
• Real-time Linux operating system

XMP-K32sx door controller can be used for intelligent access control, time recording, time management, gate control, safeguard control, camera control, parking space count, light control, for biometrical systems, RFID chip, elevator control up to 192 floors etc.

Technical details:

• Offline storage for up to
  15.000 badges (extendable via software license)
  50.000 bookings
  25.000 access profiles (extendable via software license)
• Connection for up to 4 card reader (can be extended to 8)
• Connection for up to 4 IP network cameras for event driven picture recording
• 16 supervised inputs (short cut and interruption)
• 8 outputs (1A max 24V)
• Optionally with global In/Out control in offline mode
• Network connection via integrated 10/100 MBit Ethernet connector
• 2 GB MicroSD card to store data and programs
• 64 time schedules
• 64 routines (small user programs)
• 16 graphical ViPS programs
• Calender with holiday definitions
• Elevator control with access profile for up to 192 levels using XMP-KDA-024
• Integrated UPS
• 256-bit Blowfish- or AES encryption
• Encrypted reader communication using SecuCrypt®
• Real-time Linux operating system

GPL License Text Linux-Kernel Version 2.6.15.7 / BusyBox Version 1.10.3

XMP-K32 door controller can be used for intelligent access control, time recording, time management, gate control, guard control, camera control, parking space count, light control, for biometrical systems, RFID chip, elevator control up to 192 floors etc.

Technical details:

• Offline storage for up to
  500.000 badges
  500.000 time events
  100.000 access profiles
• Connection for up to 4 card reader (can be extended to 8)
• Connection for up to 4 IP network cameras for event driven picture recording
• 16 supervised inputs (short cut and interruption)
• 8 outputs (1A max 24V)
• Optionally with global In/Out control in offline mode
• Network connection via integrated 10/100 MBit Ethernet connector
• CF card to store data and programs
• 64 time schedules
• 64 routines (small user programs)
• 16 graphical ViPS programs
• Calender with holiday definitions
• Elevator control with access profile for up to 192 levels using XMP-KDA-024
• Integrated UPS
• 256-bit Blowfish- or AES encryption
• Encrypted reader communication using SecuCrypt®
• Real-time Linux operating system

GPL License Text Linux-Kernel Version 2.6.15.7 / BusyBox Version 1.10.3

The portable device XMP-MOBILE extends the functionality of XMP-BABYLON regarding Mobile Access Control.

Typical areas of application are Access Control, Time and Attendance, Barrier Control, Ticket Checking, Picture Comparison or Guard Round.

Features:

• Robust housing for use in outdoor environments, protection class IP65
• Communication with XMP-BABYLON via WLAN, GPRS/EDGE or mobile phone (SIM card)
• 256-bit Blowfish encryption
• Real-time authorisation check of a person in online mode or offline
• Antipassback function
• XMP-MOBILE can activate the outputs of XMP Door Controllers directly
• Up to 2048 XMP-MOBILE devices may be connected to one XMP-BABYLON system
• In WLAN mode all XMP-MOBILE devices are checked and supervised continuously
• Optional integrated RFID card reader and/or 1D/2D barcode scanner
• Optional integrated 2.0M pixels camera
• Optional integrated GPS module

XMP-LRU-3000 for standard UHF applications with reading distances > 3 m, low/middle tag population (< 150)

XMP-LRU-3500 for operation in particularly disturbed and metallic environments, high tag population (> 150)

Features:

• Connection to door controller units XMP-K32, XMP-K32sx or XMP-K12
• Read range up to 12 m (XMP-LRU-3000) or up to 16 m (XMP-LRU-3500)
• Robust metal housing for use in industrial environments
• Dimensions 260 x 157 x 65 mm (10.24 x 6.18 x 2.56 inch)
• Protection class IP 53, optional IP 64 (with protection cap)
• Power supply 24V/DC (+/-5%) or Power Over Ethernet (only XMP-LRU-3500)
• Real-time Linux operating system

The Mullion Card Readers XMP-TMC2230 Hitag®/Miro and XMP-TMC2240 Hitag®/Miro are designed for use in Access Control.

XMP-TMC2230 Hitag®/Miro Reader for Access Control; connection via Door Controller XMP-K32, XMP-K32sx or XMP-K12 without pin code keyboard.

XMP-TMC2240 Hitag®/Miro Reader for Access Control; connection via Door Controller XMP-K32, XMP-K32sx or XMP-K12 with pin code keyboard.

Features:

• Reading distance from 30 to 100 mm
• Dimensions (HxLxW): 50 x 136 x 25 mm
• Encrypted data transmission activated by micro switch (SecuCrypt®)
• Firmware update via SecuCrypt® protocol
• Signaling elements: 3 LEDs, 1 buzzer
• Adjustable address via micro switch
• Integrated tamper switch
• Power supply from door controller

The Mullion Card Readers XMP-TMC2250 MIFARE® and XMP-TMC2260 MIFARE® are designed for use in Access Control.

XMP-TMC2250 MIFARE® reader for Access Control; connection via Door Controller XMP-K32, XMP-K32sx or XMP-K12 without pin code keyboard.

XMP-TMC2260 MIFARE® Reader for Access Control; connection via Door Controller XMP-K32, XMP-K32sx or XMP-K12 with pin code keyboard.

Features:

• Reading distance: from 50 to 80 mm
• Dimensions (HxLxW): 50 x 136 x 25 mm
• Encrypted data transmission activated by micro switch (SecuCrypt®)
• Firmware update via SecuCrypt® protocol
• Signaling elements: 3 LEDs, 1 buzzer
• Adjustable address via micro switch
• Integrated tamper switch
• Power supply from door controller

XMP-TMC2801-PV Readers with palm vein authentication technology are particularly suitable for high security areas.

An individual’s identity can be verified by recognizing the pattern of blood veins in the palm with near-infrared rays. Since palm vein authentication is contactless and non-invasive, Palm Vein Readers ensure a high level of user acceptance even in hygienically sensitive areas such as hospitals.

The following card variants are available:

• XMP-TMC2801-PV-HIT (Hitag®)
• XMP-TMC2801-PV-MIF (MIFARE®)
• XMP-TMC2801-PV-LEG (LEGIC®)

The XMP-TMC280x terminal has been specially designed for the Biometric Access Control. This terminal is equipped with a 2×20 digits fluorescent display, 9 special keys with 5 function keys and a numeric keyboard as well as an optical sensor for fingerprint. High flexibility enables a wide application spectrum in many areas of electronic security and automation systems.

The variants XMP-TMC2802-FP and XMP-TMC2801-FP are available as well.

For security reasons all templates (fingerprints) are stored in the XMP-K32 (host) in the secured area. After a request, for example after an identification booking or after input of a personal pin code, the current fingerscan will be send coded to the door control unit and will be compared with the current fingerprint.

Card Readers of series XMP-280x have been designed for a broad spectrum of applications, including Access Control and Time Recording in high security areas.

XMP-TMC2803 has no digital inputs and outputs. It must be connected to one of the Door Controllers XMP-K32, XMP-K32sx or XMP-K12.

Technical details:

• Protocol encryption via micro switch (SecuCrypt®)
• Firmware update via SecuCrypt® protocol
• Status display for communication (3 LEDs)
• Integrated terminal resistor, activated on demand for data transmission
• Adjustable address via micro switch
• Fluorescence display 2×20 digits
• Numeric keypad
• Integrated tamper switch
• Vandal proof housing
• Proximity card variants: MIFARE®, LEGIC®, Hitag®

Card Readers of series XMP-280x have been designed for a broad spectrum of applications, including Access Control and Time Recording in high security areas.

XMP-TMC2802 has no digital inputs and outputs. It must be connected to one of the Door Controllers XMP-K32, XMP-K32sx or XMP-K12.

Technical details:

• Protocol encryption via micro switch (SecuCrypt®)
• Firmware update via SecuCrypt® protocol
• Status display for communication (3 LEDs)
• Integrated terminal resistor, activated on demand for data transmission
• Adjustable address via micro switch
• Numeric keypad
• Integrated tamper switch
• Vandal proof housing
• Proximity card variants: MIFARE®, LEGIC®, Hitag®

Clex public is intended for partners who want to integrate Uhlmann & Zacher Clex locking units into their system. It helps the partners in creating customised solutions.

Card Readers of series XMP-280x have been designed for a broad spectrum of applications, including Access Control and Time Recording in high security areas.

XMP-TMC2801 has no digital inputs and outputs. It must be connected to one of the Door Controllers XMP-K32, XMP-K32sx or XMP-K12

Technical details:

• Protocol encryption via micro switch (SecuCrypt®)
• Firmware update via SecuCrypt® protocol
• Status display for communication (3 LEDs)
• Integrated terminal resistor, activated on demand for data transmission
• Adjustable address via micro switch
• Integrated tamper switch
• Vandal proof housing
• Proximity card variants: MIFARE®, LEGIC®, Hitag®

Clex private is the electronic locking system for use in small buildings. Whether doctors’ surgeries, law firms or private homes: with the proximity reader system from Clex private, the comfort and security of an electronic locking system is also possible in small fields of application.

The cylinders or wall readers are programmed via a service card in the Clex private system. The programming mode allows up to 1.000 transponders to be integrated into the cylinder or wall reader. Clex private does not have time zones, group or individual authorisations.

Clex private works with 125 kHz mediums such as HITAG and EM which can be interchanged within the system. In the MIFARE variant, all ISO 14443 compatible 13.5 MHz mediums can be used.

Clex private works without a PC.

Clex private can be combined with the Clex prime system.

As an electronic locking system having a wide range of products, Clex Prime meets the diverse requirements of office, industrial and administration buildings as well as the requirements of public utility buildings like hospitals or universities.

Due to the modular design of the system, a building can be randomly extended in stages and upgraded to the latest technology. This is an advantage if you want to retrofit an existing building or a building that needs to be renovated gradually.

Thanks to the 13.56 MHz MIFARE® or LEGIC® technology, HITAG or EM, Clex prime is compatible with all the other systems. For example, access control, time recording and canteen billing can be directly integrated into the Clex prime locking system using just one ID card. A further level of integration into external systems is possible using the Keyvi3 interface.

Clex prime can be combined with the Clex private system.

Locking systems having up to 60,000 cylinders and 60,000 keys are feasible in the Clex prime system.

RFID Card Readers XMP-TMC2390 HID® iCLASS® and XMP-TMC2395 HID® iCLASS® are designed for use in Access Control, Door Management, Parking System, Elevator Control etc..

XMP-TMC2390 HID® iCLASS® without keypad.

XMP-TMC2395 HID® iCLASS® with sensor keypad for PIN code input.

HID® card data format H10301 (standard 26-bit format) is supported as well as HID® format Corporate 1000 (35-bit format).

Features:

• Reading distance up to 80 mm
• Dimensions (HxLxW): 90 x 90 x 21 mm
• Encrypted data transmission activated by micro switch (SecuCrypt®)
• Firmware update via SecuCrypt® protocol
• 256-bit Blowfish or AES encrypted transmission of data
• Signaling elements: 3 LEDs, 1 buzzer
• Adjustable address via micro switch
• Integrated tamper switch
• Power supply from door controller

RFID Card Readers XMP-TMC2370 LEGIC® and XMP-TMC2380 LEGIC® are designed for use in Access Control, Door Management, Parking System, Elevator Control etc..

XMP-TMC2370 LEGIC® without keypad.

XMP-TMC2380 LEGIC® with sensor keypad for PIN code input.

LEGIC® prime / LEGIC® advant are supported.

Features:

• Reading distance up to 80 mm
• Dimensions (HxLxW): 90 x 90 x 21 mm
• Encrypted data transmission activated by micro switch (SecuCrypt®)
• Firmware update via SecuCrypt® protocol
• 256-bit Blowfish or AES encrypted transmission of data
• Signaling elements: 3 LEDs, 1 buzzer
• Adjustable address via micro switch
• Integrated tamper switch
• Power supply from door controller

RFID Card Readers XMP-TMC2350 MIFARE DESFire® and XMP-TMC2360 MIFARE DESFire® are designed for use in Access Control, Door Management, Parking System, Elevator Control etc..

XMP-TMC2350 MIFARE DESFire® without keypad.

XMP-TMC2360 MIFARE DESFire® with sensor keypad for PIN code input.

MIFARE® Classic cards are supported as well.

Features:

• Reading distance up to 60 mm
• Dimensions (HxLxW): 90 x 90 x 21 mm
• Encrypted data transmission activated by micro switch (SecuCrypt®)
• Firmware update via SecuCrypt® protocol
• 256-bit Blowfish or AES encrypted transmission of data
• Signaling elements: 3 LEDs, 1 buzzer
• Adjustable address via micro switch
• Integrated tamper switch
• Power supply from door controller

The security relay module (SRM) supplements the CX6130 wall reader with “remote actuation”. That means that the IT entry and analysis take place in a separate location from where the authorization is issued. The wall reader is connected to the security relay module, which is installed in the secure interior, via a two-pin bus connection. The users enter the data by swiping their transponder cards at the wall reader, the SRM issues the release to the corresponding door upon authorization.

There are two available relays per security relay module. The design with one relay is standard.

By separating the entry of access date and the subsequent authorized release, the problem of manipulation from the exterior is solved and thus unauthorized access is eliminated.

The remote module is an extension of the wall mounted reader by a “remote actoric unit”. That means that the reading of the key and the actual locking/unlocking take place at different locations; in the case of a wall mounted reader that means the switching of a relay.

The key is e.g. read by the wall mounted reader on the outside, the engagement of the door buzzer takes place on the secured inside by the remote module.

The number of relays required per remote module may vary considerably depending on the application. For this reason, the remote module itself has a modular design. For this purpose, it comprises a control unit (“master remote module”) that is connected to the wall mounted reader and several subunits (“slave remote modules”) serving to increase the number of relays of the whole remote module.

Per remote module, 8 relay slots are available. Up to 16 remote modules can be connected; that means that a total of 128 relays can be operated via a wall mounted reader.

The housing is suitable for DIN rail mounting.

With the Clex wall mounted reader, potential-free contacts (e.g. for electric door openers, electric locks, electric door and gate drives, elevators) are switched by means of a key shown without contact (passive transponder), by actuating an active transponder or with online devices, by pushing a button in the Keyvi3 software.

The whole electronic system incl. switching power supply, key reader unit, analysis, control unit and switching relay is located on a compact unit that can be mounted in a simple flush-mounted box. Can be used as security version in connection with the security relay module (SRM) CX6930.

By means of different covers and housings (Gira S-Color, Gira TX-44, surface- mounted, flush-mounted), manifold installation possibilities can be realized.

Available as a version with up to 128 virtualizations. Up to 128 relays, via one to 16 remote modules, can be authorized as individual units. E.g. for post office box systems or elevator controls. (This version can only be operated offline and in combination with access right on the key.)

The wall mounted reader is available as flush-mounted and surface-mounted versions for the inside and the outside.

RFID Card Readers XMP-TMC2330 Hitag® / Miro and XMP-TMC2340 Hitag® / Miro are designed for use in Access Control, Door Management, Parking System, Elevator Control etc..

XMP-TMC2330 Hitag® / Miro without keypad.

XMP-TMC2340 Hitag® / Miro with sensor keypad for PIN code input.

Hitag-1® and Hitag-2® are supported.

Features:

• Reading distance up to 100 mm
• Dimensions (HxLxW): 90 x 90 x 21 mm
• Encrypted data transmission activated by micro switch (SecuCrypt®)
• Firmware update via SecuCrypt® protocol
• 256-bit Blowfish or AES encrypted transmission of data
• Signaling elements: 3 LEDs, 1 buzzer
• Adjustable address via micro switch
• Integrated tamper switch
• Power supply from door controller

With the CX6130 wall reader, potential-free contacts (e. g. for electric door openers, electronic locks, electric doors and door motors, lifts) are activated through a (contactless) key (passive transponder) held in front of it.

All the electronics including switching power supply, key reader unit, evaluation, control unit and switching relay are located in one compact unit which can be mounted in one single flush or surface mounted box. A multitude of installation options can be realised through different blends and housings (Gira S-Color, Gira TX-44).

The CX6130 is available in a “virtual” version. Up to 128 relays, via one to 16 remote modules, must be authorised as individual units. For example for post box vestibules or lift controls.

Security version: the relay is separated in the protected inside area with its own switch unit. The wall reader is installed outside without a relay. The connection from the outside to the inside is cryptographically secured.

Transponder types: LEGIC®, active transponder (868 MHz)

XMP-TMC3500 is a powerful high end Card Reader for Access Control, Time Recording and Time Accounting

Features:

• Support for RFID technologies Hitag® 1+2, MIFARE® Classic, MIFARE® DESFire®, LEGIC® prime, LEGIC® advant, HID iClass®
• Offline support for up to 250.000 badges
• Graphical 3.5″ display with impact protected glass
• Free definable sensor keys
• Integrated 10/100 MBit Ethernet interface
• 256 Bit Blowfish or AES encrypted transmission of data
• Direct communication to other terminals and door control units
• Power supply via Power over Ethernet (PoE) or internal power supply
• 64 time schedules
• 64 routines (small user programs)
• 16 graphical ViPS programs
• Event driven picture recording from max. 2 IP cameras
• Interface for an additional card reader
• Interface for additional I/O modules
• Real-time Linux operating system

The Clex knob module for double knob cylinders with internal electronics is a battery-operated locking unit with universal application options:

Self-configurable in connection with a profile cylinder CX6780. Therefore, the following product may be generated using CX6180: CX6182.

The evaluation electronic system and the mechatronics are integrated in the knob module together with the batteries.

Thanks to the simple assembly of the Clex knob module by attaching it to the Uhlmann & Zacher Euro profile cylinder, a quick adaptation to changed requirements on site is possible.

As key, most different transponder bearers can be used at the Clex knob module. These include for example: ISO card, key fob, key of the Clex cylinder.

The Clex knob module is a battery-operated locking unit with universal application options, which is used here as follows:

Self-configurable in connection with a profile cylinder CX6740 or CX6742. Therefore, the following products may be generated using CX6140EK: CX6140, CX6142.

The communication electronic system and the mechatronics are integrated in the knob module together with the batteries.

Thanks to the simple assembly of the Clex knob module by attaching it to the Uhlmann & Zacher Euro profile cylinder, a quick adaptation to changed requirements on site is possible.

As key, most different transponder bearers can be used at the Clex knob module. These include for example: ISO card, key fob, key of the Clex lock cylinder.

The big brother of the proven Clex knob module with the protection class IP66 in accordance with Norm DIN EN 60529 was especially developed for the outdoor use. Thereby the outdoor knob is prepared against strong water jets and for humidity about 90% (not condensed).

Combined with the different components out of the Clex prime family the new outdoor knob becomes a real quick-change artist. In combination with the half cylinder it is possible to install the knob in garage doors and padlocks. If it gets set in a furniture lock adapter it becomes an electronic furniture lock. And in combination with the cylinder with the mechanical inner knob it can secure the plating. It also fits with the anti-panic-cylinder housing so it can be installed in emergency doors too.

Of course the outdoor knob – like the Clex Knob Cylinder CX6120 supports all common transponder types: EM4102, EM4450, HITAG 1, MIFARE® Classic, MIFARE® DESFire®, MIFARE® DESFire® (EV1), LEGIC® prime, LEGIC® advant, Active Transponder (868 MHz).

The CX6120 knob module is the all-rounder in the field of the Clex prime electronic locking system. Identification at the knob module can be carried out both through passive transponders (without power supply) and active transponders with their own power supply, as the knob module has already been set up for 868 MHz wireless networking as standard.

The Clex door fitting is compatible with numerous European lock standards. The different widths allow it to be used in all popular doors such as wood, steel and aluminum doors as well as doors with narrow frames having a backset of more than 25 mm. The CX6174 is therefore suitable for new buildings as well as for existing properties and because of its timeless and elegant stainless steel design, the CX6174 blends perfectly with every environment.

The reader unit with communication electronics as well as the mechanics and the power supply is located directly in the door handle.

As key, most different transponder bearers can be used at the Clex door fitting. These include for example: ISO card and key fob.

The electronic door fitting has the following extended system features:

• Time switching/daily releases possible
• Permanent engagement (toggle function) possible
• Can be connected to the IDS module CX6934
• Outdoor version being planned

Be it interior doors, storey doors or connecting doors – the electronic door handle CX6172 in a timeless stainless steel design can be installed in virtually in all commercially available doors and controls access to the doors electronically.

The complete electronics, mechanical parts, LED signaling as well as power supply have been fitted in the small space of the door handle. The installation in doors – without need for wiring or special tools – is quick and easy.

If required, the door handle can also be controlled via a radio network. Optical (red/green LEDs) and acoustic signaling allows for intuitive operation.

The electronic door handle is compatible with many European lock standards. The different versions allow it to be used in all common doors such as wood, steel and aluminum doors as well as doors with narrow frames having a backset of more than 20 mm. The CX6172 is therefore suitable for new buildings as well as for existing properties and because of its timeless and elegant stainless steel design; the CX6172 adapts perfectly to every environment.

As key, most different transponder bearers can be used at the Clex door handle. These include for example: ISO card and key fob.

The electronic fitting has a modular design which enables a simple exchange of components.

The integrated lockbox with coupling mechanisms and turning stack allows on-site adjustment for use in doors with left or right end-stop.

The reading unit with the communication electronics is located in the upper part of the fitting.

The Clex fitting is compatible with numerous European lock standards. The different widths mean it can be used in all conventional doors, such as wood, steel, aluminium and narrow framed doors from a backset of ≥ 30mm. Therefore, the CX6170 can be used in both new and existing buildings and can be adjusted to every surrounding thanks to its timeless, sleek design.

The fitting is powered by conventional 1.5V lithium batteries. Three standard lithium 1.5V batteries AA (for the broad fitting) and three standard lithium 1.5V batteries AAA (for the narrow fitting). This can power up to 150.000 lock operations (depending of the transponder technology used).

The broadest range of transponder carriers can be used with the Clex fitting as keys. These include, among others: ISO card, fob, Clex locking cylinder key.

The CX6142 consists of an electronic and coupling unit which is located inside and an antenna located in the outer knob. The CX6142 has an electronic authorisation on both sides and is already set up for 868 MHz wireless networking as standard.

The communication electronics, mechatronics and batteries are located in the knob module on the protected inner side. In the small outer knob there is just an antenna, however no energy supply or coupling mechanism at all.

The security version has special withdrawal and drilling protection mechanisms in the cylinder and outer knob. Thus the CX6142 is particularly suitable for use in exterior building doors or other doors which required a high level of mechanical protection against break-in.

Thanks to the installation of the Clex knob module using a Euro profile cylinder, conventional DIN Euro profile locks can be used and practically no extensive assembly is required. Thus the double-knob cylinder is a cost-effective solution for both new and existing buildings.

The locking cylinder is powered with two conventional CR-2 lithium batteries which can power up to 40.000 locking operations. The battery management issues 3 tones before the last closing operations to indicate that the battery needs to be changed. Using a low power adapter and servicing device, a secure opening is possible from outside even when the battery is completely flat.

The broadest range of transponder carriers can be used in the Clex knob module as keys. These include as a passive transponder (without power supply): ISO card CX6320, fob CX6330 or the transponder clip CX6340 and alternatively CX6362 as an active function transponder.

The CX6182 is used as profile cylinder with electronic freely rotatable knob on both sides. Release is brought about on both sides by electronic authorization. The evaluation electronic system and the mechatronics are integrated in the electronic knob together with the batteries on the protected inside. Only the reader electronics including an antenna with optical and acoustic signals is present in the smaller outer knob, but there is no power supply or coupling mechanism.

By means of the assembly of the CX6182 by means of a Euro profile cylinder, conventional locks for DIN Euro profiles can be used and complicated assembly is not required. This means that the double-knob cylinder is a favorably priced solution for both, new buildings and existing objects.

As key, most different transponder bearers can be used at the CX6182. These include for example: ISO card, key fob, key of the Clex cylinder.

The CX6140 consists of an electronic and coupling unit which is located inside and an antenna located in the outer knob. The CX6140 has an electronic authorization on both sides and is already set up for 868 MHz wireless networking as standard.

The communication electronics, mechatronics and batteries are located in the knob module on the protected inner side. In the small outer knob there is just an antenna, however no energy supply or coupling mechanism at all.

Thanks to the installation of the Clex knob module using a Euro profile cylinder, conventional DIN Euro profile locks can be used and practically no extensive assembly is required. Thus the double knob cylinder is a cost-effective solution for both new and existing buildings.

The CX6140 is especially suitable for tubular framed doors because it has a small knob (30 x 30 mm) on one side, which provides enough room to open the door even with small framed door backsets. The cylinder has a both one-sided and two-sided authorization, therefore the small knob can always be used on the side of the framed door which is not suitable for large knobs. The CX6140 is also suitable for exterior doors of buildings as there is only an antenna located in the small knob. Because of the two-sided electronic authorization, the inner knob spins (use on SVP locks).

The locking cylinder is powered with two conventional CR-2 lithium batteries which can power up to 40.000 locking operations. The battery management issues 3 tones before the last closing operations to indicate that the battery needs to be changed. Using a low power adapter and servicing device, a secure opening is possible from outside even when the battery is completely flat.

The broadest range of transponder carriers can be used with the Clex knob module as keys. These include as passive transponders (without power supply): ISO card CX6320, fob CX6330 or the transponder clip CX6340 and alternatively CX6362 as an active radio transponder.

The CX6126 consists of the universally applicable Clex knob module in a half cylinder CX6711.

The Clex knob module is a universally applicable, battery-powered unit which, for example, is also utilised in the cylinders CX6122 and CX6124 and is already set up for 868 MHz wireless networking as standard.

The communication technology, mechatronics and batteries are located in each knob module.

Thanks to the installation of the Clex knob module using a Euro profile cylinder, conventional DIN Euro profile locks can be used and practically no extensive assembly is required. Thus the double knob cylinder is a cost-effective solution for both new and existing buildings.

Each knob module is powered by two conventional CR-2 lithium batteries which can power up to 71.000 locking operations (depending on the transponder technology used). The battery management issues 3 tones before the last closing operations to indicate that the battery needs to be changed. The locking cylinder can always be powered from an exterior supply using a low power adapter, even with completely flat batteries.

The broadest range of transponder carriers can be used with the Clex knob module as keys. These include as passive transponders (without power supply): ISO card CX6320, fob CX6330 or the transponder clip CX6340 and alternatively CX6362 as an active radio transponder.

The CX6124 consists of two free-turning Clex knob modules in one profile cylinder. Both sides must be electronically authorized separately.

The Clex knob module is a universally applicable, battery-powered unit which, for example, is also utilized in the cylinders CX6122 and CX6126 and is already set up for 868 MHz wireless networking as standard.

The communication technology, mechatronics and batteries are located in each knob module.

Thanks to the installation of the Clex knob module using a Euro profile cylinder, conventional DIN Euro profile locks can be used and practically no extensive assembly is required. Thus the double knob cylinder is a cost-effective solution for both new and existing buildings.

Each knob module is powered by two conventional CR-2 lithium batteries which can power up to 71.000 locking operations (depending on the transponder technology used). The battery management issues 3 tones before the last closing operations to indicate that the battery needs to be changed. The locking cylinder can always be powered from an exterior supply using a low power adapter, even with completely flat batteries.

The broadest range of transponder carriers can be used with the Clex knob module as keys. These include as passive transponders (without power supply): ISO card CX6320 or the transponder clip CX6340 and alternatively CX6362 as an active radio transponder.

The CX6122 AP is a version of the CX6122, which has been developed for special use in existing emergency exits that only fulfill DIN with restraints.
Based on the CX6122, a double-knob cylinder was developed whose integrated mechanism ensures that after actuation the lock lug turns to the six o’clock position. The mechanical inner knob is has a fixed connection to the cylinder.

The Clex knob module is a universally applicable, battery-powered unit which, for example, is also utilized in the cylinders CX6124 and CX6126 and is already set up for 868 MHz wireless network as standard.

Thanks to the installation of the Clex knob module using a Euro profile cylinder, conventional DIN Euro profile locks can be used and practically no extensive assembly is required. Thus the double knob cylinder is a cost-effective solution for both new and existing buildings.

The communication technology, mechatronics and batteries are located in each knob module. The locking cylinder is powered with two conventional CR-2 lithium batteries which can power up to 71.000 locking operations (depending of the transponder technology used). The battery management issues 3 tones before the last closing operations to indicate that the battery needs to be changed. The cylinder can always be powered from an exterior power source using a low power adapter, even when the battery is completely flat.

The broadest range of transponder carriers can be used with the Clex knob module as keys. These include as passive transponders (without power supply): ISO card CX6320, fob CX6330 or the transponder clip CX6340 and alternatively CX6362 as an active function transponder.

The CX6122 consists of the universally applicable Clex knob module which is combined with a profile cylinder with an electronic free-turning knob on one side and a fixed, mechanically connected rotary knob on the other.

The Clex knob module is a universally applicable, battery-powered unit which, for example, is also utilized in the cylinders CX6124 and CX6126 and is already set up for 868 MHz wireless network as standard.

The communication technology, mechatronics and batteries are located in each knob module.

Thanks to the installation of the Clex knob module using a Euro profile cylinder, conventional DIN Euro profile locks can be used and practically no extensive assembly is required. Thus the double knob cylinder is a cost-effective solution for both new and existing buildings.

The locking cylinder is powered with two conventional CR-2 lithium batteries which can power up to 71.000 locking operations (depending of the transponder technology used). The battery management issues 3 tones before the last closing operations to indicate that the battery needs to be changed. The cylinder can always be powered from an exterior power source using a low power adapter, even when the battery is completely flat.

The broadest range of transponder carriers can be used with the Clex knob module as keys. These include as passive transponders (without power supply): ISO card CX6320, fob CX6330 or the transponder clip CX6340 and alternatively CX6362 as an active function transponder.

Amplification for your playlist: Bluetooth Connect in switch design receives and amplifies audio signals from smartphones, tablets or MP3 players in stereo quality through Bluetooth. Its operation is carried out through eight sensor keys on the elegant glass-fronted touch display. This gives you a choice of audio source, title selection, volume control, start, stop, and many more features by fingertip control. Convenient: Bluetooth Connect allows up to six different audio sources to be stored. The Bluetooth Connect internal amplifier ensures the best sound in combination with one or two JUNG loudspeaker modules. Alternatively, an external amplifier or the JUNG Smart Radio unit may be connected to an audio output. Power saving: in stand-by mode the JUNG device consumes only 0.37 W.

The new Smart Radio with stereo sound is a highlight in design and function. The display in black or white has intuitive shortcut functionalities for alarm clock, sleep timer and favorites functions. In addition, the brightness of the display and the buttons can be set separately for radio operation or night mode. In night mode the display and buttons are completely darkened, and for that reason the new radio is also perfectly suited for installation next to the bed. RDS operation, satellite and AUX inputs round out the list of features. Of course, this new JUNG radio has the accustomed top sound quality that is assured by the loudspeakers with built-in bass reflex tubes.

XMP-BABYLON is a fully configurable high-performance solution for technical and infrastructural facility management.

Characteristics of XMP-BABYLON:

• Developed for Windows 7, 8, 8.1, 2008, 2008R2, 2012, 2012R2
• Multi-user capability and network support via TCP/IP and UDP/IP
• 256-Bit Blowfish- or AES datagram encryption
• Option for additional encryption of connections using TLS V1.2
• Online monitoring of all connected devices
• Up to 2048 Door Control Units with up to 8 Card Readers per system
• Up to 500.000 badges per Door Control Unit (offline)
• Anti-passback feature, valid throughout the system, via direct internal connection
• Elevator control with authorization check for up to 192 floors
• Up to 64 workstations per system
• Up to 64 additional graphical workstations per system
• Up to 66 temporary profiles per cardholder
• Branch software for up to 128 stand-alone XMP-BABYLON systems to exchange e.g. revised data or new log entries
• A redundant XMP-BABYLON system is available as an option, which increases the operational reliability
• 64 open software interfaces enable communication with third-party systems (e.g. SAP® R/3® HR via TCP/IP)
• Integration of monitoring and control functions within the building management system
• Unlimited number of graphics to visualize alarms and processes
• Video log
• Integration of digital video recording systems, e.g. Bosch® VMR, Geutebrück® GeViScope, NiceVision®, Dallmeier electronic®, NETAVIS®, HeiTel®
• Optional user-defined Time Recording and Accounting
• Guard tour patrol system for monitoring e.g. security guards at appointed checkpoints
• Transmission of alarms via e-mail or text message
• Interfaces to key cabinet systems
• Software interface for transmission of XMP-BABYLON alarms to external CCTV systems
• Contamination monitoring in the pharmaceuticals industry to ensure time-limited access restrictions
• Software to export alarm- and event- log entries and cardholder records to a SQL database
• Integration of third-party systems via OPC-Server / OPC-Client
• Workflow
• Integrated SNMP server
• Announcement of visitors using a web interface as an additional option

The VoIP-OEM board for audio/video transmission contains already the following interfaces: Ethernet, 10/100BaseT, Power-over-Ethernet (802.3af), 2Wire interface (optional), high-speed USB port, connector for touch LCD, digital camera interface, analog video port, analog audio port with microphone and speaker input, serial expansion port with UART and I2C for card reader etc., trigger input or Wiegand input and output, RS485 or relay or Wiegand output, and Micro-SD card.

Web Services based management software to synchronize any number of Adatis devices on the network OS independent – works with most popular web browsers – no client software installation required.

The Adatis DoorKeeper is an easy-to-use application designed specifically for visitor communication and access control. With DoorKeeper, any number of doors that are equipped with Adatis access systems can be remote-controlled from any location over the world.

The Adatis DoorKeeper is an easy-to-use application designed specifically for visitor communication and access control. With DoorKeeper, any number of doors that are equipped with Adatis access systems can be remote-controlled from any location over the network.

In connection with an Adatis door terminal the CommandCenter takes over the indoor station: If it rings, the camera picture will automatically appear in the display. The communication can be started with a fingertip or the door can be opened. The CommandCenter automatically adjusts the brightness of the display of the current situation and switches on automatically when it is approached. If it is not used, it runs in the power saving mode.

FaceUP integrates the latest biometric face detection technology with the proven installation in any flush mount box. This is achieved by a consequent miniaturization of the camera and processing unit.

The FaceEntry-XS allows the biometric verification of card holders. As a pure access terminal, it is equipped with a 2D face detection and PIN code as standard. Optionally available is the 3D face detection for maximum security and an RFID reader.

The TouchEntry-XS ensures a high level visitor communication: The VoIP data is transmitted according to the SIP standard, a high echo suppression is achieved by full duplex. In addition, there is already a database installed for up to 10,000 entries. Thanks to the Fisheye lens, you can even get a panoramic image of your entrance area at your remote location.

Visitors either choose their desired point of contact directly using the built-in phone book – or ring the door bell for the receptionist. As the unit is networked, distance does not matter any more and the receiving station can be anywhere in the world. The high quality echo cancellation guarantees natural voice communication, without losing a word. At the same time you will see the person and the situation in front of the door, live and in color, anytime, even if no one is ringing.

Face recognition is safe, quick and easy to use and works without physical contact. The Adatis-technology is working with a three-dimensional acquisition of the face in invisible infrared light. When a face in front of the camera is detected, a 3D scan is started and features generated from the 3Dmesh are compared against features stored in a database. If the person standing in front of the door is enrolled, i.e. in the data base, the door opens automatically.

The intelligent control of your comfortable temperature: with intelligent KNX building technology, temperature control has never been more convenient! Whether by pressing a button, by touch screen or with a mobile app, as part of the KNX system you simply integrate your temperature control with all other building technology functions and enjoy pure living comfort!

For a clear head, the right concentration of carbon dioxide in the room is an important factor. If it is too high, we lose concentration, get headaches and performance is reduced. Especially in rooms where a lot of people are present at the same time, for example, classrooms, this can happen quickly. With a CO2 multi-sensor, you can counter this: If the threshold values are reached, it operates window openers or the ventilation system and ensures that the air in the room has an optimum quality.

Air humidity plays a decisive role for a healthy indoor environment. If it is too high, fungus can grow – and that is neither attractive nor healthy! With the Humidistat technology from JUNG you regulate the air humidity based on room temperature and thus provide an optimum environment.

Ideal temperature pre-programmed: you control the room temperature time-controlled and in accordance with your needs using thermostats. That is not only extremely convenient, but also helps to save energy! Simply feel good, without heating unused rooms at the same time. You also match the design of your light switches etc.

Whether for radiators on the wall or for floor heating: with the standard heating control units you simple set the room temperature individually with the setting wheel, completely as you wish. With the variety of JUNG switch designs, you can match the control units harmoniously to the rest of the electrical fittings in the room.

Using the Smart Remote App you can easily control all the functions in a KNX installation while remaining mobile – everything from the lighting, blinds and temperature up to the multimedia system – via an iPhone, iPad or iPod touch.